LOCONETOPSBOARD
Servo 1 Address
On Time CV value
Servo 1 Move Range
Servo 2 Move Range
Servo 3 Move Range
Servo 4 Move Range
None
Restart the SC8
Move servos to center position
Move servos back and forth
Move servos to one end
Move servos to the other end
Test State
Version ID
Manufacturer ID
Servo 1 Center Position
Servo 2 Center Position
Servo 3 Center Position
Servo 4 Center Position
Servo 2 Address
Servo 3 Address
Servo 4 Address
Servo 5 Address
Servo 6 Address
Servo 7 Address
Servo 8 Address
Power On Send Input State
Power On Send Output State
Interrogate input
Interrogate output
Mode 1 - Servos 2 Pos
Mode 2 - Servos 3 Pos
Mode
Select Power On Option
Option 2
DCC gateway
Bus interface
DCC control
Ops Mode Address
b
t
c
b
t
c
b
t
c
b
t
c
b
t
c
b
t
c
b
t
c
b
t
c
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Address
Invert
Toggle
Switch Request
Switch Feedback
Sensor Message
Type
No Message
Send on Rising Edge
Send on Falling Edge
Send on Both Edges
Transition
Route Number
Servo 1 Move Speed D1
Servo 2 Move Speed D1
Servo 3 Move Speed D1
Servo 4 Move Speed D1
Servo 5 Move Speed D1
Servo 6 Move Speed D1
Servo 7 Move Speed D1
Servo 8 Move Speed D1
Servo 1 Move Speed D2
Servo 2 Move Speed D2
Servo 3 Move Speed D2
Servo 4 Move Speed D2
Servo 5 Move Speed D2
Servo 6 Move Speed D2
Servo 7 Move Speed D2
Servo 8 Move Speed D2
Start up delay
Address
Servo 1 Behavior - Speed to Position
Reverse
Servo 2 Behavior - Speed to Position
Reverse
Servo 3 Behavior - Speed to Position
Reverse
Servo 4 Behavior - Speed to Position
Reverse
Reverse
Reverse
Reverse
Reverse
Servo 5 Move Range
Servo 6 Move Range
Servo 7 Move Range
Servo 8 Move Range
Servo 5 Center Position
Servo 6 Center Position
Servo 7 Center Position
Servo 8 Center Position
Route send delay
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Top Address
t
c
Switch State
No
Yes
Sensor Route Execution
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
Cell 1 Address
t
c
Switch State
Cell 2 Address
t
c
Switch State
Cell 3 Address
t
c
Switch State
Cell 4 Address
t
c
Switch State
Cell 5 Address
t
c
Switch State
Cell 6 Address
t
c
Switch State
Cell 7 Address
t
c
Switch State
Cell 8 Address
t
c
Switch State
------ SC8 Output Addresses ------
Use this number to set the address number
of the device the output is connected to.
------ Basic Operation ------
------ Notes: ------
The Custom Programmer format is recommended
Basic
Note: Changes to Option CVs are not recognized until SC8 power is cycled.
------ Decoder Configuration CV29 ------
------ Communication Options ------
Opt4 Enable gateway for DCC commands from track to bus
- Requires bus interface and DCC control to be enabled
Opt5 Enable transmit and receive on bus
Opt6 Enable receiving DCC commands from track
- When disabled, DCC gateway is disabled
Note: In a Digitrax system the bus is called LocoNet
------ Special Options ------
Opt2 Enable operations mode programming
This is the same as a Loco address
------ Status Report CV28 ------
------ Options ------
Opt1 Send output state at power on
- Switch type messages
Opt2 Send output state at Digitrax interrogation request
- Feedback type messages
Options
---- Sets the SC8 to a particular test state - Use to help adjust servos ----
Only works in Ops mode
Changes the value of CV7 (Version ID) as displayed in DP
Test State may change when Version ID is read
Mfg
------ Input 1 ------
------ Input 2 ------
------ Input 3 ------
------ Input 4 ------
------ Input 5 ------
------ Input 6 ------
------ Input 7 ------
------ Input 8 ------
Inputs
When a switch (turnout) throw command is issued that matches this address the SC8 inputs are disabled.
When a close command is issued with this address the inputs are enabled.
This feature is useful for dispatcher control when the SC8 inputs are used for local turnout control.
Input lockout address
Input Lockout
---- Servo Configuration ----
Servo 5 Behavior -
Servo 6 Behavior -
Servo 7 Behavior -
Servo 8 Behavior -
---- Sets the output state to always be the same at power on ----
Output#
Both
Throw
Close
1
2
3
4
5
6
7
8
Outputs
Note: If a sensor message is selected to execute a route then
switch state c and t is used for sensor hi and lo respectively.
------ Route 1 ------
------ Route 2 ------
------ Route 3 ------
------ Route 4 ------
------ Route 5 ------
------ Route 6 ------
------ Route 7 ------
------ Route 8 ------
Routes
CVs