Decoder Family: Stationary Decoder

CV Definitions:

CVNamePositionsValues
1VVVVVVVV
    2XVVVVVVV
      3XVVVVVVV
        5VVVVVVVV
          7XXXXXVVV
          1. None
          2. Restart the Servette
          3. Move servos to center position
          4. Move servos back and forth
          5. Move servos to one end
          6. Move servos to the other end
          7
            8
              10XVVVVVVV
                11XVVVVVVV
                  12VVVVVVVV
                    14VVVVVVVV
                      16VVVVVVVV
                        18VVVVVVVV
                          20VVVVVVVV
                            22VVVVVVVV
                              24VVVVVVVV
                                26VVVVVVVV
                                  29XXXXXVVV
                                  1. Mode 1 - Servo 2 Pos, output 2 has unique address
                                  2. Mode 2 - Servo 2 Pos, output 2 has servo address
                                  3. Mode 3 - Servo 3 Pos, output 2 has unique address
                                  4. Not used -do not select
                                  5. Mode 4 - Inputs control servo, output 2 has unique address
                                  29XXXXVXXX
                                  1. No
                                  2. Yes
                                  29XXXVXXXX
                                  1. No
                                  2. Yes
                                  29XXVXXXXX
                                  1. No
                                  2. Yes
                                  31XVVVVVVV
                                    33XXXXXXVV
                                    1. b
                                    2. t
                                    3. c
                                    34XXXXXXVV
                                    1. t
                                    2. c
                                    36XXXXXXVV
                                    1. Input Disabled
                                    2. On Low to High Transition
                                    3. On High to Low Transition
                                    4. On Change Transition
                                    36VVVVXXXX
                                      36XXXXVVXX
                                      1. Close
                                      2. Throw
                                      3. Toggle
                                      44XXXXXXVV
                                      1. Input Disabled
                                      2. On Low to High Transition
                                      3. On High to Low Transition
                                      4. On Change Transition
                                      44VVVVXXXX
                                        44XXXXVVXX
                                        1. Close
                                        2. Throw
                                        3. Toggle
                                        67XVVVVVVV
                                          71XXXXXXVV
                                          1. None
                                          2. Sequence or rotate
                                          3. Speed to Position
                                          71VXXXXXXX
                                          1. no
                                          2. yes
                                          75XXXXXXVV
                                          1. None
                                          2. Will flash when servo is in the cw position
                                          3. Will flash when servo is in the ccw position
                                          Basic ------ Servette Output Addresses ------ Use this number to set the address number of the device the output is connected to. ------ Special Functions ------ This is the same as a Loco address ------ Notes: ------ The Custom Programmer format is recommended Mfg ---- Sets the Servette to a particular test state - Use to help adjust servos ---- Only works in Ops mode Changes the value of CV7 (Version ID) as displayed in DP Test State may change when Version ID is read Inputs ------ Primary Input Control 1 ------ ------ Secondary Input Control 1 ------ Outputs ---- Servo Configuration ---- ---- Output Flashing ---- ---- Sets the output state to always be the same at power on ---- Only applies if Option 1 is selected Servette Both Throw Close Relay Throw Close Routes ---- Remote Control Route Address ---- CVs
                                          This page was produced by JMRI.

                                          Copyright © 1997-2021 JMRI Community.

                                          JMRI, DecoderPro, PanelPro, DispatcherPro and associated logos are our trademarks.

                                          Additional information on copyright, trademarks and licenses is linked here.