Short address A value of 255 corresponds to 100% See RP 9.2.2 for more information. Values from 2 to 127 indicate preloaded speed tables. 0 or 1 means not used. Values between 128 and 154 define the cab throttle position where the mid range decoder speed value is applied Disable Enable stop when Right Rail has +ve asymetric signal Enable stop when Left Rail has +ve asymetric signal Enable stop when either Rail has +ve asymetric signal Allows Automatic stop on detection of Assymetric signal 0=Disable, 1=Right Rail, 2= Left Rail, 3= Both Rails Disabled Constant Broadcast Broadcast on Asymetric Signal Used to configure ZTC Talkback 0= Talkback OFF, 1= Constant Broadcast, 2= Broadcast on detection of Asymetric Signal normal reversed 14 speed step format 28 speed step format NMRA Digital only DC conversion enabled Disabled Enabled Use Vstart, Vmid, Vhigh Use table in CVs 66 through 95 One byte (short) address Two byte (extended) address No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes Sets the constant Braking Distance for auto stopping 0-255 Output is ON or OFF On/Off 8 times per second On/Off 3.5 times per second On/Off 2.5 times per second On/Off 2 times per second On/Off every second On/Off every 2 seconds On/Off every 4 seconds On for 0.05 seconds then Off On for 0.1 seconds then Off On for 0.2 seconds then Off On for 0.3 seconds then Off On for 0.4 seconds then Off On for 0.5 seconds then Off On for 0.6 seconds then Off On for 0.7 seconds then Off On for 0.8 seconds then Off On for 0.9 seconds then Off On for 1 second then Off Dim Level 1. This is the dimmest setting Dim Level 2. Dim Level 3. Dim Level 4. Dim Level 5. Dim Level 6. Dim Level 7. Dim Level 8. Dim Level 9. Dim Level 10. Dim Level 11. Dim Level 12. Dim Level 13. Dim Level 14. Dim Level 15. Dim Level 16. This is the brightest setting Mars effect Beacon effect Flame effect Ashpan effect Output is ON or OFF On/Off 8 times per second On/Off 3.5 times per second On/Off 2.5 times per second On/Off 2 times per second On/Off every second On/Off every 2 seconds On/Off every 4 seconds On for 0.05 seconds then Off On for 0.1 seconds then Off On for 0.2 seconds then Off On for 0.3 seconds then Off On for 0.4 seconds then Off On for 0.5 seconds then Off On for 0.6 seconds then Off On for 0.7 seconds then Off On for 0.8 seconds then Off On for 0.9 seconds then Off On for 1 second then Off Dim Level 1. This is the dimmest setting Dim Level 2. Dim Level 3. Dim Level 4. Dim Level 5. Dim Level 6. Dim Level 7. Dim Level 8. Dim Level 9. Dim Level 10. Dim Level 11. Dim Level 12. Dim Level 13. Dim Level 14. Dim Level 15. Dim Level 16. This is the brightest setting Mars effect Beacon effect Flame effect Ashpan effect Output is ON or OFF On/Off 8 times per second On/Off 3.5 times per second On/Off 2.5 times per second On/Off 2 times per second On/Off every second On/Off every 2 seconds On/Off every 4 seconds On for 0.05 seconds then Off On for 0.1 seconds then Off On for 0.2 seconds then Off On for 0.3 seconds then Off On for 0.4 seconds then Off On for 0.5 seconds then Off On for 0.6 seconds then Off On for 0.7 seconds then Off On for 0.8 seconds then Off On for 0.9 seconds then Off On for 1 second then Off Dim Level 1. This is the dimmest setting Dim Level 2. Dim Level 3. Dim Level 4. Dim Level 5. Dim Level 6. Dim Level 7. Dim Level 8. Dim Level 9. Dim Level 10. Dim Level 11. Dim Level 12. Dim Level 13. Dim Level 14. Dim Level 15. Dim Level 16. This is the brightest setting Mars effect Beacon effect Flame effect Ashpan effect No Yes 0=OFF, 1=ON Insert comment Insert comment No Yes Enables ZTCs own slow running mode allows fine tuning of the speed range ZTC